WhatsApp: +86 15921799893     E-mail:sales@slinord.com

Centrifugal Casting Explained: Why Hollow Rings, Sleeves & Tubes Come Out Denser

Nov .04.2026
  Views

For solid parts, sand or investment casting usually comes first to mind. But when your component is hollow, round, and round on the inside — a sleeve, bushing, liner, roll shell, tube, or ring — one process often beats both: centrifugal casting.

Used for centuries to turn spinning motion into metallurgical soundness, centrifugal casting remains the preferred route for high-quality cylindrical and hollow parts. Here's how it works, where it wins, and when you should ask a foundry for it.

How Centrifugal Casting Works

The principle is straightforward but powerful: molten metal is poured into a rotating mold, and centrifugal force presses it against the inner wall while it solidifies.

  1. A cylindrical metal mold spins rapidly on a horizontal (or, less often, vertical) axis.
  2. Molten metal is poured into the spinning cavity.
  3. Centrifugal acceleration throws the metal outward, building a uniform wall against the mold surface.
  4. Solidification progresses from the mold wall inward, directionally and under pressure.
  5. The mold stops, and the finished hollow casting is removed and further processed.

That outward force isn't just a convenience. It changes the quality of the metal itself.

Why the Process Produces Better Hollow Parts

1. Denser, Sounder Structure

Because the metal is consolidated under G-force, gases and light impurities are pushed toward the free inner surface instead of becoming trapped in the wall. Porosity shrinks, density rises, and the wall between the outside bore and the final inner surface ends up substantially sounder than a statically cast equivalent.

2. Minimal or No Risers / Gates

Static castings need feeders (risers) to compensate for solidification shrinkage — wasted metal that later returns to scrap. Centrifugal action feeds the cavity naturally, so material usage and runner losses drop sharply on long production runs.

3. Excellent Outer Surface and Concentricity

The outer surface forms against a smooth, rotating mold wall, producing a clean, dimensionally consistent outer diameter. The casting's axis stays concentric, reducing the machining stock needed on the OD and helping sleeves and liners seat properly.

4. Natural Alloy Segregation Control

In wear-resistant and high-alloy grades, the process encourages the dense, hard constituents toward the load-bearing region of the wall, which directly benefits parts like bushings and liners that wear radially.

The Parts It Makes Best

Centrifugal casting shines on rotationally symmetric, hollow components:

Product type

Typical use

Cast steel / iron sleeves and bushings

Bearing seats, pivot wear sleeves

Barrel and liner castings

Pump barrels, cylinders, crusher liners

Roll shells & roll rings

Mill rolls, work rolls, support rolls

Hollow tubes & pipes

Wear-resistant pipe, pressure piping

Gear rings, flanges, circular wear bands

Rings that demand sound cross-sections

These are exactly the kinds of parts where internal voids, uneven wall thickness, or a porous bore would cause early failure — and where centrifugal consolidation pays for itself.

Which Alloys Suit It

Centrifugal casting handles a broad range of ferrous alloys:

  • Cast steel grades — for structural hollow parts requiring weldability and toughness.
  • High-chromium white irons — abrasion-resistant sleeves and liners where hard carbides give wear life.
  • Martensitic and heat-resistant steels — rolls, high-temperature rings, and furnace hardware.
  • Stainless and duplex grades — corrosion-resistant tubes and liners.

Alloy choice still follows the service conditions (wear, impact, heat, corrosion) — the process only delivers the geometry and soundness that make the alloy perform.

Where Centrifugal Casting Is Not the Answer

It is not a universal substitute:

  • Solid, non-cylindrical parts cannot be made this way; use sand or investment casting.
  • Short, complex profiles with bosses, holes, or irregular contours add tooling and finishing cost without a clear benefit.
  • Very small precision components with intricate detail are usually better produced by investment casting, which wins on surface finish and geometry.
  • Ultra-thin or extremely long sections are limited by the machine's envelope and spinning capability.

In short: think centrifugal casting when the part is essentially a thick-walled, round, hollow cylinder.

Centrifugal vs. the Other Two Processes at a Glance

Factor

Centrifugal

Sand Casting

Investment Casting

Ideal geometry

Hollow round / ring / tube

Any, esp. large & simple

Complex, intricate

Internal soundness

Very good under G-force

Depends on feed system

Good, near-net shape

Wall density for sleeves

Excellent

Prone to shrinkage

Less relevant

Material efficiency

High (few risers)

Lower (feeder waste)

Moderate

Surface finish (OD)

Good against mold

Rough

Smooth as-cast

Best at volume

Long sleeve/liner runs

Large simple parts

Precision small–medium parts

What to Ask Your Foundry Before Ordering

  1. What mold length and inner/outer diameter range can they spin?
  2. What wall thickness range and tolerance can they hold?
  3. Which alloys do they regularly spin, and do they supply soundness test records (UT, density, macroetch)?
  4. Can they do rough machining, finish bore, or only as-cast?
  5. What inspection proves a sound wall — NDT or section sampling?

A capable centrifugal shop won't just quote weight; it will confirm whether your part shape and alloy actually belong on the spinner.

Built For Endurance

At SLINORD, our casting capabilities extend across the parts industry needs — including sound, wear-resistant hollow components produced where the geometry and service conditions call for it. We match process to part: centrifugal for the dense rings and sleeves, sand or investment casting where geometry and volume demand it.

Contact us with your part drawing or cross-section, and we'll recommend the process and alloy that give you a durable, sound casting.


SLINORD — China Precision Casting Factory · Custom Iron & Steel Casting Supplier · Built For Endurance


Related News
Machining Allowance & Tolerance Tips for Casting Drawings: Design It Rig
Machining Allowance & Tolerance Tips for Casting Drawings: Design It Rig
Nov .16.2026
A casting drawing is where cost is won or lost — long before the first chip is cut.
Centrifugal Casting Explained: Why Hollow Rings, Sleeves & Tubes Come Out De
Centrifugal Casting Explained: Why Hollow Rings, Sleeves & Tubes Come Out De
Nov .04.2026
For solid parts, sand or investment casting usually comes first to mind. But when your component is hollow, round, and round on the inside — a sleeve, bushing, ...
Heat-Resistant Steel Castings Inside Your Furnace: Why the Right Alloy Extends C
Heat-Resistant Steel Castings Inside Your Furnace: Why the Right Alloy Extends C
Oct .31.2026
Inside a batch or continuous heat-treatment furnace, the structural hardware rarely gets the attention it deserves. Most plant teams focus on the parts being pr...
Custom Casting, Step by Step: From Your Drawing to a Finished Part
Custom Casting, Step by Step: From Your Drawing to a Finished Part
Oct .26.2026
Ordering a custom casting shouldn‘t feel like a leap of faith. But for many buyers, the process between "send your drawing" and "receive your par...