WhatsApp: +86 15921799893     E-mail:sales@slinord.com

Common Casting Defects and How to Reject a Bad Part on Arrival

Oct .22.2026
  Views

Your casting arrived. You signed the delivery note. Then, three weeks into service, it cracks.

Here's the uncomfortable truth: many casting defects are visible on arrival — if you know what to look for. Learning to recognize them before the part goes into your machine is the difference between a five-minute inspection and a $50,000 downtime event.

This guide covers the most common defects, what they look like, and how to catch them at incoming inspection.

The Big Four Casting Defects

1. Gas Porosity (Pinholes & Gas Holes)

What it is: Small round cavities or pinholes on the surface, caused by gas trapped in the metal as it solidifies.

What it looks like: Smooth, rounded holes scattered on the surface or exposed on a machined face. On machined surfaces they appear as small shiny craters.

How it fails: Porosity reduces the effective cross-section and creates stress concentrators — a part can look fine and still break at a porous spot under load.

2. Shrinkage (Shrinkage Cavities & Porosity)

What it is: Irregular, branched cavities formed where molten metal couldn't feed a heavy section as it solidified.

What it looks like: Ragged, rough-walled cavities, often in thick sections or near risers. On a broken or machined surface, it can look like a sponge or a jagged void.

How it fails: Severe shrinkage is a guaranteed fracture path. It's often internal, which is why non-destructive testing (UT, X-ray) matters on critical parts.

3. Sand Inclusions & Slag

What it is: Foreign material — sand, refractory, or slag — trapped in the casting.

What it looks like: Discolored, rough spots on the surface that don't match the metal; cavities filled with gritty material. On machined faces they appear as embedded specks.

How it fails: Inclusions act as weak points and can cause leaks or cracking, especially in pressure-tight or fatigue-loaded parts.

4. Cracks & Tears (Hot Tear / Cold Crack)

What it is: Cracks formed during solidification (hot tear) or after cooling (cold crack).

What it looks like: A thin, often jagged line on the surface. Hot tears are usually oxidized and discolored; cold cracks are sharp and clean.

How it fails: A crack is a fatigue initiator. Even a small surface crack can grow into a catastrophic failure in a vibrating or cyclically loaded component.

How to Inspect a Casting on Arrival

Do these checks before you sign off or before you machine anything:

  1. Clean it first. Remove coatings, scale, and oil. Many defects hide under a thin layer of shop dirt.
  2. Good light. Use a bright, angled light. Porosity and inclusions catch light differently than sound metal.
  3. Look at every surface. Rotate the part and inspect all faces, not just the ones you'll see in assembly.
  4. Check machined faces carefully. If the casting has a machined surface, it's your best window into internal soundness.
  5. Weigh it. A significantly light part can indicate internal shrinkage — worth a closer look.
  6. Magnify the suspicious spots. A simple 10× loupe turns a "probably fine" surface into a clear call.

The Inspection Matrix

Defect

What it looks like

Best detection

Gas porosity

Smooth round pinholes/craters

Visual on machined face

Shrinkage

Ragged internal cavities

UT, X-ray, sectioning

Sand/slag inclusion

Gritty discolored spots

Visual, magnetic particle

Cracks & tears

Thin jagged lines

Visual, dye penetrant (PT)

When to Reject, When to Accept

Not every defect is grounds for rejection. The decision depends on location, size, and your application:

  • A small cosmetic pit on a non-critical surface may be acceptable — if the drawing and standard allow it.
  • The same pit on a machined sealing face, or in a fatigue-loaded zone, is a reject.
  • Internal shrinkage that's beyond the acceptance standard is always a reject for structural parts.

The right approach: define acceptance criteria with your foundry in writing before production, so both sides inspect against the same standard — not a fight after the parts arrive.

Where Defects Come From — and Who's Responsible

Defects trace to specific process causes:

  • Porosity → moisture, dirty charge, wrong pouring temperature, poor gating.
  • Shrinkage → poor riser design, wrong gating, heavy isolated sections.
  • Inclusions → mold/sand quality, slag handling, turbulence during pour.
  • Cracks → restrained contraction, wrong alloy, uneven cooling, bad heat treatment.

A good foundry uses defects as a feedback loop — finding one on your part means they fix the process so it doesn't recur. A bad one hides it and hopes you don't look.

Built For Endurance

At SLINORD, we inspect against documented acceptance standards, run NDT where it matters, and treat every defect as a process problem to fix — not a shipment to push through.

Contact us  with your drawing, and we'll define the acceptance criteria and inspection plan for your part before we pour a single casting.


SLINORD — China Precision Casting Factory · Custom Iron & Steel Casting Supplier · Built For Endurance


Related News
Machining Allowance & Tolerance Tips for Casting Drawings: Design It Rig
Machining Allowance & Tolerance Tips for Casting Drawings: Design It Rig
Nov .16.2026
A casting drawing is where cost is won or lost — long before the first chip is cut.
Centrifugal Casting Explained: Why Hollow Rings, Sleeves & Tubes Come Out De
Centrifugal Casting Explained: Why Hollow Rings, Sleeves & Tubes Come Out De
Nov .04.2026
For solid parts, sand or investment casting usually comes first to mind. But when your component is hollow, round, and round on the inside — a sleeve, bushing, ...
Heat-Resistant Steel Castings Inside Your Furnace: Why the Right Alloy Extends C
Heat-Resistant Steel Castings Inside Your Furnace: Why the Right Alloy Extends C
Oct .31.2026
Inside a batch or continuous heat-treatment furnace, the structural hardware rarely gets the attention it deserves. Most plant teams focus on the parts being pr...
Custom Casting, Step by Step: From Your Drawing to a Finished Part
Custom Casting, Step by Step: From Your Drawing to a Finished Part
Oct .26.2026
Ordering a custom casting shouldn‘t feel like a leap of faith. But for many buyers, the process between "send your drawing" and "receive your par...